Sign in Start free trial
Help centre › Tinting

Cutter bridge and cut queue

Send cuts from a cutboard straight to your USB, serial or network cutter, follow them in the cut queue, and see which patterns and cutters cause problems.

What it is

The EZI cutter bridge is a small program for the computer your film cutter (plotter) is connected to. The Cut queue is the list of cuts waiting for, being sent to, or already sent to each cutter. Together they replace "download the .plt file, open the cutter's software, import, cut".

Who uses it

  • Owner / manager: connects each cutter once and reads the Pattern & cutting report.
  • Cutting staff: press Send to cutter queue on a cutboard and record the result.
  • Technicians: use the At the car phone page to tick pieces off, mark a pattern as fitting, or report a problem.

Why it matters

Fewer steps means fewer mistakes: the exact pattern versions on the board are what gets cut, the cut is recorded against the job and roll, and failures are visible to everyone instead of lost on one computer.

How to connect a cutter (once)

  1. Tinting → Patterns & cutting → Plotters. Add the cutter if it is not there and calibrate it.
  2. In the cutter's Desktop bridge box press Connect a desktop bridge. Copy the key - it is shown only once.
  3. Download the bridge from the blue note at the top of the Plotters page and follow its setup (Python 3, then python ezi_cutter_bridge.py --setup). Choose how the cutter is connected: network (IP:port), serial (COM port), device (USB device path or a shared Windows printer) or printer (macOS/Linux printer name).
  4. Run --test to cut a 50 mm square, then start the bridge normally. The Plotters page shows ● online.

How to cut

  1. Build the board on Cutboards & cuts as usual and clear the pre-flight checks.
  2. Press Send to cutter queue (shown when the board's cutter has a bridge). You are taken to the Cut queue.
  3. Within a few seconds the status goes in the cutter queue → sending to cutter → sent to cutter.
  4. When the film is peeled, open the cutboard and press Cut OK, take film (enter the film pulled if it differs) or Failed with a note. This takes the film off the roll and costs it to the job.

You can still press Make cut file (.plt) to download the file instead.

Cut queue statuses

Status Meaning What to do
in the cutter queue Waiting for the bridge Make sure the bridge window is open
sending to cutter The bridge has taken it Wait
sent to cutter The cutter received it Record the result on the cutboard
could not reach cutter Cutter off, cable, wrong address Fix, then Send again
cancelled Taken out before it was sent Send again if needed
cut / failed Result recorded -

At the car (phone page)

Open a job and press At the car (also on My day). It shows the car, the instructions, big Check in / Check out and Take photos buttons, and every piece cut for this job with its outline. Tick pieces as you fit them, press Fits to record a passed fit test, or Problem to report what is wrong (photos from the phone camera allowed). A critical or blocking problem flags the pattern for review straight away.

Pattern & cutting report

Patterns & cutting → Pattern & cutting report (managers): cuts, success rate, cuts that never reached the cutter, film pulled and average waste - by cutter and by month - and a pattern table with open problems and failed fit tests at the top, so the patterns that waste film get fixed first.

Rules & limits

  • One cut at a time per cutter, oldest first. If the bridge closes mid-send, the cut returns to the queue after 10 minutes.
  • A bridge key only lets the program fetch cuts for its own cutter and report sending; it can't see anything else. Make a new bridge key cancels the old one immediately.
  • Files are checked with a checksum before cutting; a damaged file is refused.
  • Recording Cut OK is still a human step - the bridge only knows the cutter received the file.

Tips

  • Keep the bridge running on the cutting-room PC and set it to start with Windows.
  • If a network cutter doesn't respond, check its IP on the cutter's panel and that the raw port (often 9100) is enabled.

Related: Cutboards, cut files and plotters, Pattern library.